Solare-datensysteme Solar-Log Manual de usuario Pagina 129
- Pagina / 242
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
129
Special functions
•
Automatic timer
The automatic time profile operators independent of the current PV production. Up to 10 periods can
be defined based on the time.
•
Performance Visualization
The performance visualization profile can be used in connection with the Solar-Log™ Smart Relay Box.
The Relay Box has 8 relays. The relays can be switched on in stages. The value for the activation the
individual relays needs to be defined.
•
Threshold and Time Control
With this profile, appliances can be controlled based on the configured switching thresholds and also
with optional automatic timer settings. An upper threshold for activation and a lower threshold for
deactivation need to be configured. Additionally, a time period can be defined in which the appliance
is switched on or off if this has not already been done via the threshold control. The minimum duration
the appliance has to be switched on for is defined in the previous duration box. If this duration is not
covered with the threshold control, the appliance is switched on for the entire defined duration.
Procedure:
•
Open the Configuration | Special functions | Smart Home dialog.
•
Select Profile position.
•
Select Type.
•
Activate Profile via the switch.
•
Select the Switch
This switch has to be configured in the
Configuration | Devices | Smart-Home menu.
•
Enter the typical Nominal power in watts.
•
Enter the profile dependent parameters/
•
SAVE settings.
Generation Information on Thresholds
Five-minute values are generated to balance the fluctuations in PV production (e.g. due to clouds) for
managing appliances. The average value is aligned to the threshold set in the respective logic control.
Generation Information on typical nominal power�
The typical nominal power is the average consumption of appliances that is controlled by the profile.
Appliances, such a laundry dryer, have a short high peak of power consumption and times in which little
power is required. Based on this, it would be problematic to calculate the current power consumption for
power management control. For this reason, the Solar-Log™ calculates with the configured value for typi-
cal nominal power during the entire duration of operation.
Note
When configuring the control logic make sure to allocate profile positions so that the
power supply (for surpluses) is adjusted to the priority of the managed appliances.
- Installation manual 1
- Solar-Log™ 1
- Table of Contents 3
- 1 Introduction 10
- Notes for the Firmware Update 11
- External 12
- 4 Safety information 13
- 5 Electric current 14
- 6 Package contents 15
- 7 Wall mounting 16
- Note concern 17
- 8 Unit connections 18
- Bottom connections 19
- 8�2 Solar-Log 300 20
- Top connections 20
- 8�3 Solar-Log 500 22
- 8�4 Solar-Log 1000 24
- 8�5 Solar-Log 1200 26
- 8�6 Solar-Log 2000 28
- 9 Optional Connections 30
- Optional Connections 31
- 9�3 Solar-Log™ PM+ 33
- RS485 - A 36
- PIN Assignment 36
- 10�3 RS485/422 - B 37
- RS485/422 C 38
- 10�5 S0 39
- 10�5�1 S0-IN B 39
- S0_OUT_IN 40
- 10�6 PM+ 41
- 11 Connecting the inverters 42
- Connecting the inverters 43
- Switching inverters off 43
- Switching the Solar-Log™ off 43
- 12 Connecting accessories 44
- Connecting accessories 46
- Notes on roof mounting 46
- 12�3 Ripple Control Receiver 49
- 12�4 Large External Displays 50
- 12�5 External power meter 52
- 12�6 Wiring for S0 meter 54
- 12�7 Wiring for RS485 meter 56
- Caution 60
- 1 22 - B 61
- 4 23 - A 61
- 1 Data + (Y) 62
- 4 Data - (G) 62
- Relay output assignments 63
- 13 Other connections 64
- 13�3 USB 65
- 14 Installation 66
- Installation 67
- Requirements 67
- Easy Installation 67
- Device URL 70
- 14�6 Using the browser menu 72
- Control elements 73
- Control element Meaning 73
- 15 Main menu 74
- 16 Configuration Menu 75
- 16�2 Ethernet 76
- Configuration Menu 77
- PUK entry 79
- Status and Test section 79
- Status section 81
- 16�5 Proxy 83
- 17 Internet Configuration 84
- 17�3 E-mail 85
- E-mail settings section 85
- 17�4 Text message (SMS) 86
- 18�1 Device definition 88
- Section RS485-B 89
- Network section 89
- Switch configuration menu 90
- Configuring connected devices 91
- Home or Smart Energy 91
- Operating mode: 92
- Input definition section 93
- Reference voltage section 93
- 18�4 Device Detection 94
- 18�5 Configuring devices 95
- 18�5�1 Configuring inverters 95
- 18�5�3 Configuring sensors 96
- Example: 97
- Operating modes: 98
- 18�5�6 Module Fields 99
- Example module fields: 99
- 18�7 Battery 100
- 19 Configuring Plant Data 101
- 19�2 Plant groups 102
- 19�3 Graphic 102
- Yearly target section 103
- Tariff settings 104
- Configuring Plant Data 105
- Self-consumption mode 105
- Configuration 105
- 105
- 20 Configuring Notifications 107
- 20�2 Device notifications 108
- Status and fault codes 108
- Filter status and fault codes 109
- 20�3 Yield 110
- Notifications per e-mail 110
- Test section 111
- 20�5 Power & Failure 111
- Save multiple 112
- Save all 113
- 20�6 PM 113
- 21 Editing Data 114
- 21�2 Data correction 115
- 21�3 System backup 115
- 21�4 Backup 117
- 21�5 Reset 119
- Restore factory settings 120
- 22 System Configuration 121
- 22�2 Language/Country/Time 122
- Language section 122
- Country section 122
- Time section 123
- 22�3 Display 124
- Dimming at a certain time 124
- Dimming after inactivity 124
- Check for Update from USB 126
- Automatic Firmware Updates 126
- System Configuration 127
- 23 Special functions 128
- 23�2 Feed-In Management 130
- 23�2�1 Plant parameters 130
- Plant passwords 131
- 23�2�2 Active power 132
- Interface section 132
- LCD Display 132
- Special functions 133
- fixed reduction 136
- settings 137
- 23�2�8 Adjustable reduction 138
- 23�3 Reactive Power 139
- Reactive Power Management 141
- Reductions 141
- Select remote controlled 146
- Select options 146
- SAVE settings 146
- 23�5 Profile 149
- 23�6 Direct Marketing 151
- Procedure 152
- SAVE the settings 152
- 24�1 Display menu structure 153
- 24�3 Settings on the device 154
- Procedure: 155
- 24�6 Basic settings menu 159
- 24�7 USB menu 160
- Saving all data section 160
- Firmware update section 161
- Configuration with the keypad 163
- Mode Action Key 163
- 25�5 Configuring inverters 167
- 25�5�5 Power meter via RS485 168
- 25�6 Internal Settings 169
- 25�6�1 Reset 169
- ENTER to save 170
- 26�2 Display menu structure 172
- 26�3 Configuration Menu 172
- 26�4 Initial configuration 173
- System settings 173
- Network Settings section 173
- 26�4�2 Inverter selection 174
- IP Address, Subnet Mask 176
- Internet access 176
- Settings for analog modem 177
- Settings for GPRS modem 177
- 26�7 Defining Plant groups 179
- Changing the name 180
- Changing the inverter data 180
- Configuring graphic scaling 183
- Start Initial Configuration 187
- Config. 187
- How to make data corrections: 188
- Delete data 190
- Select the desired country 192
- Unit connections 193
- Symbol Meaning 195
- 27�1�1 Fault messages 197
- 27�3 Normal operation 198
- 27�4 Power reduction 198
- 28�1 LED status indications 199
- 29 Faults 201
- Restarting 202
- 29�2 Fault messages 204
- 29�2�1 Fault messages GPRS 204
- 29�2�2 Fault messages time 205
- 29�2�3 Fault messages WiFi 205
- Fault messages Internet 206
- Conguration 206
- Network 207
- Fault messages Export (FTP) 207
- 29�3�3 Special cases 212
- 30 Disposal 213
- 31 Technical Data 214
- Interfaces 215
- General Data 215
- Top Features Solar-Log 216
- Solar-Log 216
- Basic functions 217
- Plant monitoring 217
- Visualization 218
- Interface 218
- Top Features 219
- Inverter interface 220
- Technical Data 221
- 32 Appendix 222
- Appendix 223
- Country Inverter brand 223
- Configuration in browser menu 228
- Active Power 228
- K3 K4 K5 233
- 32�5 Digital Interfaces 235
- 32�5�1 Modbus TCP 235
- 32�5�2 JSON Interfaces 237
- JSON Objects 238
- 32�6 Dimensions 239
- 33 List of Figures 240
- List of Figures 241
Relacionado con productos y manuales para Accesorios para el aire Solare-datensysteme Solar-Log
Accesorios para el aire Solare-datensysteme RS485 Funkpaket/ Radio Set Manual de usuario
(17 paginas)
(17 paginas)
Accesorios para el aire Solare-datensysteme Solar-Log Sensor Box Professional Plus Manual de usuario
(24 paginas)
(24 paginas)
Accesorios para el aire Solare-datensysteme Solar-Log WEB Classic 2nd Edition Manual de usuario
(7 paginas)
(7 paginas)
Accesorios para el aire Solare-datensysteme Smart Energy mit Solar-Log Manual de usuario
(31 paginas)
(31 paginas)
Accesorios para el aire Solare-datensysteme Solar-Log Smart Relais Station Manual de usuario
(21 paginas)
(21 paginas)
Accesorios para el aire Solare-datensysteme Solar-Log Handbuch SMS Konfiguration Manual de usuario
(9 paginas)
(9 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.138 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales